| Brand | Castle Group |
|---|---|
| Measurement | Hand Arm Vibration, Whole Body Vibration |
The Ultimus Vibration Meter is straightforward to use and is supplied with everything you need to take vibration exposure measurements, including a handstrap accelerometer and PC Software.
The Ultimus is fully compliant and meets all the necessary standards, including: ISO8041:2005, ISO 2631-1,2&5, ISO 5349.
With datalogging features, your data is stored on the 16MB non-volatile memory card. Reults and data can then be easily downloaded to a PC for data analysis using the provided software.
| Standards | ISO 8041:2005, ISO 2631-1,2&5, ISO 5349 |
| Meter Mode | RMS, VDV, MTVV or Max, Peak, Peak-Peak, Vector, A(8), Dose, ELV, EAV Simultaneous measurement in six channels with independent set of filters and detector constants |
| Filters | Wd, Wk, Wm, Wb (ISO 2631) and Wh (ISO 5349) and Band Limiting filters |
| RMS and RMQ Detectors | Digital true RMS & RMQ detectors with Peak detection, resolution 0.1 dB Time constants from 100 ms to 10 s |
| Data Logger | Time-history data including meter mode results and spectra (option) |
| Time Domain Recording | Simultaneous x, y, z time-domain signal recording, sampling frequency selectable: 375 Hz, 3 kHz or 6 kHz (option) |
| Analyser | 1/1 octave real-time analysis with centre frequencies from 0.5 Hz to 2000 Hz 1/ octave real-time analysis with centre frequencies from 0.4 Hz to 2500 Hz |
| Measurement Range | Transducer dependent: 0.01 ms2 RMS ÷ 50 ms2 Peak (with SV 38V and Wd filter) 0.1 ms2 RMS ÷ 5000 ms2 Peak (with SV105A and Wh filter) |
| Frequency Range | 0.1 Hz ÷ 2000 Hz |
| Input | 2 x LEMO 5-pin: six channels IEPE type or Direct and two channels for force transducers |
| Dynamic Range | 90 dB |
| Force Range | 0.2 N ÷ 100 N (dedicated channels for force transducers) |
| Sampling Rate | 6kHz |
| Memory | Internal 16 MB non-volatile memory Micro SD flash card slot |
| Interfaces | USB 1.1 Client, Extended I/O - AC output (1 V Peak) or Digital Input/Output (Trigger - Pulse) |
| Power Supply | Four AA batteries (alkaline) - operation time > 12 h (6.0 V / 1.6 Ah)2/ Four AA rechargeable batteries (not included) - operation time > 16 h (4.8 V / 2.6 Ah)2 USB interface - 500 mA HUB |
| Environmental Conditions | Temperature from -10°C to 50°C/ Humidity up to 90% RH, non-condensed |
| Dimensions | 140 x 83 x 33 mm (without accelerometer) |
| Weight (Approx) | 390 grams including batteries (without accelerometer) SV105A Accelerometer |
| Performance | Number of axis: 3 Sensitivity (± 5 %): 10.2 mV/(m/s2) at 15.915 Hz, HP1 |
| Measurement Range | 0.024 ms-2 RMS,Wh ÷ 180 ms-2 PEAK |
| Frequency Response (± 3 dB) | 1 Hz ÷ 2763 Hz |
| Resonant Frequency | 5.5 kHz (MEMS transducer) |
| Electrical Noise | < 240 µV RMS, Wh weighting, < 2.2 mV RMS, HP1 weighting |
| Electrical | Supply current: < 5,0 mA |
| Supply Voltage | 5.2 V ÷ 16 V Bias voltage (IEPE): 2,5 V ± 0.05 V |
| Output Impedance | 51 Ω Charge / discharge time constant (start-up time): 30 sec. typ. TEDS memory: installed (power supply pin) |
| Environmental Conditions | Maximum vibration: 980 m/s2 shock survival for MEMS sensor |
| Temperature Coefficient | <+0.012 dB/°C/ Temperature: from -10°C to +50°C |
| Humidity | up to 90 % RH, non-condensed |
| Physical | Sensing element: MEMS |
| Cable | integrated 1.4 meters long |
| Connector | LEMO 5-pin plug (GA2007 compatible) |
| Dimensions | 69.6 mm x 31.4 mm dimension; thickness from 8.3 mm to 15 mm |
| Weight | 50-60 grams (including cable and one of vibration contact adapters) |
